| AMI UC210-31C4HR5 Mounted Units & Inserts | d:100 mm; Mass inner ring:0.8 kg; r, r1,2 min.:1.1 mm; B:40 mm; F:115 mm; |
| AMI MUCHPL202RFB Hanger Unit Bearings | Fillet Radius rb:1.00 mm; Oil Speed Rating n2:1500 rpm; B:104.00 mm; Basic Static Radial Load Rating Co:710000 N; D:320.0000 mm; Fillet Radius ra:3.00 mm; Grease Speed Rating n1:1100 rpm; Basic Dynamic Radial Load Rating C:449000 N; d:180.000 mm; |
| AMI UCST211-32NPMZ2 Take Up Unit Bearings | Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; d:5 mm; Tolerance shaft:e7; Tolerance housing:H7; Coefficient of friction µ min.:0.08; Mass bushing:0.005 kg; Permissible sliding velocity v max.:0.5 m/s; Specific dynamic load factor K:25 N/mm²; B:10 mm; |
| AMI UEFC207-23NPMZ20 Mounted Units & Inserts | Contact seal:2 x B9784-15; Initial grease fill:31.185 g; Mass pillow block:6.19 kg; Cap bolt recommended tightening torque:61 N·m; RG:1/8 NPT; P150°:9.79 kN; Max. speed for contact seal:3400 r/min; P120°:11.1 kN; Cap bolt, SAE grade:5; P90°:17.3 kN; |
| AMI MUCFT207-22NPRF Mounted Units & Inserts | B:25.4 mm; Basic static load rating C0:106 kN; Cb min.:4.5 mm; r3,4 min.:0.8 mm; Basic dynamic load rating C:99.1 kN; Ca min.:5 mm; db min.:57 mm; d1 ≈:62.2 mm; C:19.05 mm; a:16.993 mm; |
| AMI UCMFL201-8MZ20 Mounted Units & Inserts | α:124 °; Specific dynamic load factor K:25 N/mm²; Coefficient of friction µ min.:0.08; a:12.5 mm; Mass bushing:17.3 kg; D:260 mm; h:242.5 mm; d:240 mm; Tolerance housing:H7; Specific static load factor K0:45 N/mm²; |
| AMI MUCFT205NPRF Mounted Units & Inserts | Reference speed:430 r/min; s max.:5 mm; Calculation factor e:0.3; Db max.:567 mm; Calculation factor Y:0.4; Mass bearing:44 kg; d:460 mm; B:72 mm; d1 ≈:501 mm; Limiting speed:530 r/min; |
| AMI UFL006CE Flange Block Bearings | D1 ≈:113 mm; Reference speed:900 r/min; da min.:181 mm; Minimum load factor A:7.7; Mass bearing (including seat washer where applicable):20 kg; Da max.:159 mm; Fatigue load limit Pu:34.5 kN; D:230 mm; ra max.:2.5 mm; r1,2 min.:3 mm; |
| AMI UGCJTZ205-16 Flange Block Bearings | Cb min.:9 mm; r1,2 min.:2 mm; ra max.:2 mm; Calculation factor Y0:0.8; Calculation factor Y:1.5; rb max.:1.5 mm; B:38 mm; Basic static load rating C0:236 kN; Reference speed:4500 r/min; Fatigue load limit Pu:26.5 kN; |
| AMI UFL004 Flange Block Bearings | S:4.763 mm; P120°:249 kN; dc:193.675 mm; Appropriate attachment bolt size G:1.5 in; Bearing limiting speed:1500 r/min; Housing:SAFS 340; P150°:222 kN; ba:103.188 mm; Mass pillow block:417 kg; R2:50.8 mm; |
| AMI KHP210 Mounted Units & Inserts | Specific dynamic load factor K:10 N/mm²; B:6 mm; Permissible sliding velocity v min.:0.25 m/s; Coefficient of friction µ min.:0.05; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; Specific static load factor K0:20 N/mm²; Mass bushing:0.002 kg; D:12 mm; d:8 mm; |
| AMI UCSTX13-40NP Take Up Unit Bearings | d:70.000 mm; Fillet Radius ra:2.00 mm; Oil Speed Rating n2:3800 rpm; Basic Dynamic Radial Load Rating C:153000 N; Sealed Speed Rating n3:2800 rpm; Basic Static Radial Load Rating Co:125000 N; D:150.0000 mm; Grease Speed Rating n1:2800 rpm; Accessories:One Shield; B:63.50 mm; |
| AMI UCAO308-24 Pillow Block Bearings | Mass inner ring:0.053 kg; B:30 mm; r, r1,2 min.:0.3 mm; F:30 mm; d:25 mm; |
| AMI UGCJTZ209-26 Flange Block Bearings | A2:254 mm; RG:3/4 NPT; Appropriate attachment bolt size G:1 in; ba:75.406 mm; N1:28.575 mm; Pa:46.3 kN; A1:180.975 mm; h:60.325 mm; Cap bolt:1-8 UNC; P150°:173 kN; |